Zakładka z wyszukiwarką danych komponentów |
|
AD7171BCPZ-REEL7 Arkusz danych(PDF) 10 Page - Analog Devices |
|
AD7171BCPZ-REEL7 Arkusz danych(HTML) 10 Page - Analog Devices |
10 / 16 page AD7171 Rev. 0 | Page 10 of 16 750 ADC CIRCUIT INFORMATION OVERVIEW The AD7171 is a low power ADC that incorporates a precision 16-bit Σ-Δ modulator and an on-chip digital filter intended for measuring wide dynamic range, low frequency signals. The device has an internal clock and one differential input. It operates with an output data rate of 125 Hz and has a gain of 1. A 2-wire interface simplifies data retrieval from the AD7171. FILTER, DATA RATE, AND SETTLING TIME The AD7171 uses a sinc3 filter. The output data rate is set to 125 Hz; thus, valid conversions are available every 1/125 = 8 ms. If a reset occurs, then the user must allow the complete settling time for the first conversion after the reset. The settling time is equal to 24 ms. Subsequent conversions are available at 125 Hz. When a step change occurs on the analog input, the AD7171 requires several conversion cycles to generate a valid conversion. If the step change occurs synchronous to the conversion period, then the settling time of the AD7171 must be allowed to generate a valid conversion. If the step change occurs asynchronous to the end of a conversion, then an extra conversion must be allowed to generate a valid conversion. The data register is updated with all the conversions but, for an accurate result, the user must allow the required time. Figure 12 shows the filter response of the filter. The only external filtering required on the analog inputs is a simple R-C filter to provide rejection at multiples of the master clock. A 1 KΩ resistor in series with each analog input, a 0.01 μF capacitor from each input to GND, and a 0.1 μF capacitor from AIN(+) to AIN(−) are recommended. 0 –100 –90 –80 –70 –60 –50 –40 –30 –20 –10 0 625 500 375 250 125 INPUT SIGNAL FREQUENCY (Hz) Figure 12. Filter Response GAIN The AD7171 has a gain of 1. The acceptable analog input range is +VREF. Therefore, with VREF = 5 V, the input range is +5 V. POWER-DOWN/RESET(PDRST) The PDRST pin functions as a power-down pin and a reset pin. When PDRST is taken low, the AD7171 is powered down. The entire ADC is powered down (including the on-chip clock), and the DOUT/RDY pin is tristated. The circuitry and serial interface are also reset. This resets the logic, the digital filter, and the analog modulator. PDRST must be held low for 100 ns minimum to initiate the reset function (see ). Figure 4 When PDRST is taken high, the AD7171 is taken out of power- down mode. When the on-chip clock has powered up (1 ms, typically), the modulator then begins sampling the analog input. The DOUT/RDY pin becomes active, going high until a valid conversion is available. A reset is automatically performed on power-up. ANALOG INPUT CHANNEL The AD7171 has one differential analog input channel that is connected to the modulator; that is, the input is unbuffered. Note that this unbuffered input path provides a dynamic load to the driving source. Therefore, resistor/capacitor combinations on the input pins can cause dc gain errors, depending on the output impedance of the source that is driving the ADC input. Table 7 shows the allowable external resistance/capacitance values such that no gain error at the 16-bit level is introduced. Table 7. External R-C Combination for No Gain Error C (pF) R (Ω) 50 9 k 100 6 k 500 1.5 k 1000 900 5000 200 The absolute input voltage range is restricted to a range between GND − 30 mV and VDD + 30 mV. Care must be taken in setting up the common-mode voltage to avoid exceeding these limits. Otherwise, there is degradation in linearity and noise performance. BIPOLAR CONFIGURATION The AD7171 accepts a bipolar input range. A bipolar input range does not imply that the part can tolerate negative voltages with respect to system GND. Signals on the AIN(+) input are referenced to the voltage on the AIN(−) input. For example, if AIN(−) is 2.5 V, the analog input range on the AIN(+) input is 0 V to 5 V when a 2.5 V reference is used. |
Podobny numer części - AD7171BCPZ-REEL7 |
|
Podobny opis - AD7171BCPZ-REEL7 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |