Zakładka z wyszukiwarką danych komponentów
  Polish  ▼
ALLDATASHEET.PL

X  

AD588KQ Arkusz danych(PDF) 4 Page - Analog Devices

Numer części AD588KQ
Szczegółowy opis  High Precision Voltage Reference
Download  12 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Producent  AD [Analog Devices]
Strona internetowa  http://www.analog.com
Logo AD - Analog Devices

AD588KQ Arkusz danych(HTML) 4 Page - Analog Devices

  AD588KQ Datasheet HTML 1Page - Analog Devices AD588KQ Datasheet HTML 2Page - Analog Devices AD588KQ Datasheet HTML 3Page - Analog Devices AD588KQ Datasheet HTML 4Page - Analog Devices AD588KQ Datasheet HTML 5Page - Analog Devices AD588KQ Datasheet HTML 6Page - Analog Devices AD588KQ Datasheet HTML 7Page - Analog Devices AD588KQ Datasheet HTML 8Page - Analog Devices AD588KQ Datasheet HTML 9Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 12 page
background image
REV. D
–4–
AD588
THEORY OF OPERATION
The AD588 consists of a buried Zener diode reference, amplifiers
used to provide pin programmable output ranges, and associ-
ated thin-film resistors as shown in Figure 1. The temperature
compensation circuitry provides the device with a temperature
coefficient of 1.5 ppm/
°C or less.
R3
RB
R1
R2
R4
R5
R6
GAIN
ADJ
GND
SENSE
+IN
GND
SENSE
–IN
VLOW BAL
ADJ
VCT A4 IN
–VS
+VS
A4 OUT
FORCE
A4 OUT
SENSE
A3 OUT
FORCE
A3 OUT
SENSE
A3 IN
VHIGH
NOISE
REDUCTION
A1
A4
AD588
A3
A2
Figure 1. AD588 Functional Block Diagram
Amplifier A1 performs several functions. A1 primarily acts to
amplify the Zener voltage from 6.5 V to the required 10 V output.
In addition, A1 also provides for external adjustment of the
10 V output through Pin 5, GAIN ADJ. Using the bias compen-
sation resistor between the Zener output and the noninverting
input to A1, a capacitor can be added at the NOISE REDUCTION
pin (Pin 7) to form a low-pass filter and reduce the noise contri-
bution of the Zener to the circuit. Two matched 10 k
Ω nominal
thin-film resistors (R4 and R5) divide the 10 V output in half.
Pin VCT (Pin 11) provides access to the center of the voltage
span and Pin 12 (BAL ADJ) can be used for fine adjustment
of this division.
Ground sensing for the circuit is provided by amplifier A2. The
noninverting input (Pin 9) senses the system ground, which
will be transferred to the point on the circuit where the invert-
ing input (Pin 10) is connected. This may be Pin 6, 8, or 11.
The output of A2 drives Pin 8 to the appropriate voltage. Thus, if
Pin 10 is connected to Pin 8, the VLOW pin will be the same
voltage as the system ground. Alternatively, if Pin 10 is con-
nected to the VCT pin, it will be ground and Pin 6 and Pin 8 will
be +5 V and –5 V, respectively.
Amplifiers A3 and A4 are internally compensated and are used
to buffer the voltages at Pins 6, 8, and 11, as well as to provide a
full Kelvin output. Thus, the AD588 has a full Kelvin capability
by providing the means to sense a system ground and provide
forced and sensed outputs referenced to that ground.
APPLYING THE AD588
The AD588 can be configured to provide +10 V and –10 V
reference outputs as shown in Figures 2a and 2c, respectively. It
can also be used to provide +5 V, –5 V, or a
± 5 V tracking
reference, as shown in Figure 2b. Table I details the appropriate
pin connections for each output range. In each case, Pin 9 is
connected to system ground and power is applied to Pins 2 and 16.
The architecture of the AD588 provides ground sense and
uncommitted output buffer amplifiers that offer the user a great
deal of functional flexibility. The AD588 is specified and tested
in the configurations shown in Figure 2a. The user may choose
to take advantage of the many other configuration options available
with the AD588. However, performance in these configurations
is not guaranteed to meet the extremely stringent data sheet
specifications.
As indicated in Table I, a +5 V buffered output can be provided
using amplifier A4 in the +10 V configuration (Figure 2a). A –5 V
buffered output can be provided using amplifier A3 in the –10 V
configuration (Figure 2c). Specifications are not guaranteed for
the +5 V or –5 V outputs in these configurations. Performance
will be similar to that specified for the +10 V or –10 V outputs.
As indicated in Table I, unbuffered outputs are available at
Pins 6, 8, and 11. Loading of these unbuffered outputs will
impair circuit performance.
Amplifiers A3 and A4 can be used interchangeably. However,
the AD588 is tested (and the specifications are guaranteed) with
the amplifiers connected as indicated in Figure 2a and Table I.
When either A3 or A4 is unused, its output force and sense pins
should be connected and the input tied to ground.
Two outputs of the same voltage may be obtained by connect-
ing both A3 and A4 to the appropriate unbuffered output on
Pins 6, 8, or 11. Performance in these dual-output configura-
tions will typically meet data sheet specifications.
CALIBRATION
Generally, the AD588 will meet the requirements of a precision
system without additional adjustment. Initial output voltage
error of 1 mV and output noise specs of 10
µV p-p allow for
accuracies of 12 bits to 16 bits. However, in applications where
an even greater level of accuracy is required, additional calibra-
tion may be called for. Provision for trimming has been made
through the use of the GAIN ADJ and BAL ADJ pins (Pins 5 and
12, respectively).
The AD588 provides a precision 10 V span with a center tap
(VCT) that is used with the buffer and ground sense amplifiers to
achieve the voltage output configurations in Table I. GAIN
ADJUST and BALANCE ADJUST can be used in any of these
configurations to trim the magnitude of the span voltage and
the position of the center tap within the span. The GAIN
ADJUST should be performed first. Although the trims are not
interactive within the device, the GAIN trim will move the
BALANCE trim point as it changes the magnitude of the span.


Podobny numer części - AD588KQ

ProducentNumer częściArkusz danychSzczegółowy opis
logo
Analog Devices
AD588 AD-AD588_15 Datasheet
505Kb / 20P
   Multiple Output, High Precision, Dual-Tracking Reference
Rev. L
More results

Podobny opis - AD588KQ

ProducentNumer częściArkusz danychSzczegółowy opis
logo
Texas Instruments
REF6225 TI1-REF6225 Datasheet
1Mb / 35P
[Old version datasheet]   High-Precision Voltage Reference
logo
Analog Technologies, In...
ATREF500 ANALOGTECHNOLOGIES-ATREF500 Datasheet
155Kb / 3P
   High Precision Voltage Reference
6/12/2021
logo
Microchip Technology
MCP1501 MICROCHIP-MCP1501_V01 Datasheet
13Mb / 39P
   High-Precision Buffered Voltage Reference
Revision G February 2022
MCP1501 MICROCHIP-MCP1501 Datasheet
1Mb / 36P
   High-Precision Buffered Voltage Reference
07/14/15
MCP1502 MICROCHIP-MCP1502 Datasheet
18Mb / 28P
   High-Precision Buffered Voltage Reference
Revision A September 2021
logo
Cirrus Logic
VRE104 CIRRUS-VRE104 Datasheet
643Kb / 5P
   Precision Voltage Reference
VRE310 CIRRUS-VRE310 Datasheet
602Kb / 5P
   Precision Voltage Reference
VRE304 CIRRUS-VRE304 Datasheet
541Kb / 4P
   Precision Voltage Reference
VRE205 CIRRUS-VRE205_10 Datasheet
641Kb / 4P
   Precision Voltage Reference
logo
DATEL, Inc.
PVR-1540SM DATEL-PVR-1540SM Datasheet
98Kb / 1P
   Precision Voltage Reference
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12


Arkusz danych Pobierz

Go To PDF Page


Link URL




Polityka prywatności
ALLDATASHEET.PL
Czy Alldatasheet okazała się pomocna?  [ DONATE ] 

O Alldatasheet   |   Reklama   |   Kontakt   |   Polityka prywatności   |   Linki   |   Lista producentów
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com