Zakładka z wyszukiwarką danych komponentów |
|
AD9040A Arkusz danych(PDF) 7 Page - Analog Devices |
|
AD9040A Arkusz danych(HTML) 7 Page - Analog Devices |
7 / 12 page AD9040A REV. B –7– In applications using multiple AD9040As, slaving the reference inputs to a single reference output will improve gain tracking among the ADCs, as shown in Figure 5. VOUT VREF AD9040A 0.1 F –VS VREF AD9040A VREF AD9040A –VS –VS 0.1 F 0.1 F 0.1 F 0.1 F 0.1 F Figure 5. Slaving Multiple AD9040As to a Single Internal Reference In the specifications table, the Gain Tempco parameter under DC ACCURACY applies to the ADC when the internal refer- ence is being used. If an external reference is used, its tempera- ture coefficient must be taken into account to determine overall temperature performance. The input range can be varied by adjusting the reference voltage applied to the AD9040A. By decreasing the reference voltage, the gain can be reduced approximately 10% with no degrada- tion in performance. Increasing the reference voltage increases the gain; but for proper operation, the reference voltage should not exceed +2.6 V. Time-Gain Control ADC Ultrasound and sonar systems require an increase in gain versus time. This allows the system to correct for attenuation of return pulses. Figure 6 shows the AD600/AD602 amplifier and the AD9040A ADC configured as a time-gain control analog-to- digital converter. The control voltage ramps from –625 mV to +625 mV, permitting 40 dB of gain-control range. The voltage used for gain control can be either a linear ramp, or the output of a voltage-output DAC such as the AD7242. AD9040A AIN –625mV +625mV GAIN CONTROL VOLTAGE AD600/602 Figure 6. Ultrasound/Sonar Time-Gain Control ADC Using X-AMPs™ Transient Response Figure 7 illustrates the method for evaluating ADC transient performance. Two synthesizers are locked in synchronization, but tuned to frequencies which are slightly offset from a 2-to-1 submultiple. One synthesizer clocks a flat pulse network at a frequency of 19.9609375 MHz to provide the analog input signal; the other synthesizer output is shaped to provide a CMOS 40 MHz sam- pling clock. At the output of the AD9040A, output data reflects an interleaved alias of the input pulse. The repetitive sampling allows the measurement of ADC transient response as shown in performance graphs elsewhere in this data sheet. AD9040A MARCONI 2030 SYNTHESIZER REF MARCONI 2030 SYNTHESIZER REF 19.9609375 MHz 40 MHz FLAT PULSE NETWORK SINE TO CMOS ANALOG IN ENCODE OUTPUT Figure 7. Transient Response Test X-AMP is a trademark of Analog Devices, Inc. |
Podobny numer części - AD9040A |
|
Podobny opis - AD9040A |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |