Zakładka z wyszukiwarką danych komponentów |
|
LM3350 Arkusz danych(PDF) 5 Page - National Semiconductor (TI) |
|
|
LM3350 Arkusz danych(HTML) 5 Page - National Semiconductor (TI) |
5 / 8 page Detailed Operation (Continued) STEP-UP APPLICATIONS NEED AN EXTRA DIODE The LM3350 is biased from pin V high. Thus for step-up appli- cations, an external Schottky diode (D1) is needed to supply power to V high during startup (See Figure 2). Note that during shutdown, this diode will provide a DC path from V in to Vout. The load may therefore continue to draw current from the in- put voltage source. This Schottky diode is not required for step-down applications (See Figure 3). SHUTDOWN MODE When ENABLE is a logic low (ground), the LM3350 enters a low power shutdown mode. In this mode, all circuitry is dis- abled and therefore, all switching action stops. During shut- down, the current consumption drops to 250 nA (typical). When ENABLE is a logic high, (i.e. 3.3V for step-up mode and 5.0V for step-down mode), the LM3350 returns to nor- mal operation. Application Information CAPACITOR SELECTION The LM3350 requires four capacitors: an input bypass ca- pacitor (connected between V in and ground), an output hold capacitor (connected between V out and ground), and two sampling capacitors (C1 and C2 in Figures 2, 3). 0.33 µF (±20%) ceramic chip type capacitors are recommended for all four capacitors. The usable operating frequency should be greater than 5 MHz for all capacitors. The input bypass capacitor (C in) is the least critical. Its value should be at least that of the sampling capacitors. While the recommended sampling capacitor values are 0.33 µF, other values may be selected. Values other than 0.33 µF affect maximum output current rating and efficiency. Figure 1 shows typical output impedance (Z out) versus capacitor value. The output hold capacitor value determines the output ripple. Increasing the value of the hold capacitor decreases the ripple. The value of this capacitor (C out) can be calculated (approximately) based on the output ripple ( ∆V out) require- ments from: where I load is the load current and fO is the oscillator fre- quency. In order to ensure superior performance over the entire oper- ating temperature range, capacitors made of X7R dielectric material are suggested. However, capacitors made of other dielectric materials that still meet the ±20% specification over the entire temperature range can also be used. PRECAUTIONS The LM3350 is not short circuit protected. DS100002-11 A. Step-Up Mode DS100002-12 B. Step-Down Mode FIGURE 1. Z out vs. C www.national.com 5 |
Podobny numer części - LM3350 |
|
Podobny opis - LM3350 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |