Zakładka z wyszukiwarką danych komponentów |
|
ADC0803 Arkusz danych(PDF) 11 Page - Renesas Technology Corp |
|
ADC0803 Arkusz danych(HTML) 11 Page - Renesas Technology Corp |
11 / 17 page ADC0803, ADC0804 FN3094 Rev 4.00 Page 11 of 17 August 2002 IC voltage regulators may be used for references if the ambient temperature changes are not excessive. Zero Error The zero of the A/D does not require adjustment. If the minimum analog input voltage value, VlN(MlN), is not ground, a zero offset can be done. The converter can be made to output 0000 0000 digital code for this minimum input voltage by biasing the A/D VIN(-) input at this VlN(MlN) value (see Applications section). This utilizes the differential mode operation of the A/D. The zero error of the A/D converter relates to the location of the first riser of the transfer function and can be measured by grounding the VIN(-) input and applying a small magnitude positive voltage to the VIN(+) input. Zero error is the difference between the actual DC input voltage which is necessary to just cause an output digital code transition from 0000 0000 to 0000 0001 and the ideal 1/2 LSB value (1/2 LSB = 9.8mV for VREF/2 = 2.500V). Full Scale Adjust The full scale adjustment can be made by applying a differential input voltage which is 11/2 LSB down from the desired analog full scale voltage range and then adjusting the magnitude of the VREF/2 input (pin 9) for a digital output code which is just changing from 1111 1110 to 1111 1111. When offsetting the zero and using a span-adjusted VREF/2 voltage, the full scale adjustment is made by inputting VMlN to the VIN(- ) input of the A/D and applying a voltage to the VIN(+) input which is given by: , where: VMAX = the high end of the analog input range, and VMIN = the low end (the offset zero) of the analog range. (Both are ground referenced.) Clocking Option The clock for the A/D can be derived from an external source such as the CPU clock or an external RC network can be added to provIde self-clocking. The CLK IN (pin 4) makes use of a Schmitt trigger as shown in Figure 16. Heavy capacitive or DC loading of the CLK R pin should be avoided as this will disturb normal converter operation. Loads less than 50pF, such as driving up to 7 A/D converter clock inputs from a single CLK R pin of 1 converter, are allowed. For larger clock line loading, a CMOS or low power TTL buffer or PNP input logic should be used to minimize the loading on the CLK R pin (do not use a standard TTL buffer). Restart During a Conversion If the A/D is restarted (CS and WR go low and return high) during a conversion, the converter is reset and a new conversion is started. The output data latch is not updated if the conversion in progress is not completed. The data from the previous conversion remain in this latch. Continuous Conversions In this application, the CS input is grounded and the WR input is tied to the INTR output. This WR and INTR node should be momentarily forced to logic low following a power-up cycle to insure circuit operation. See Figure 17 for details. Driving the Data Bus This CMOS A/D, like MOS microprocessors and memories, will require a bus driver when the total capacitance of the data bus gets large. Other circuItry, which is tied to the data bus, will add to the total capacitive loading, even in three-state (high- impedance mode). Back plane busing also greatly adds to the stray capacitance of the data bus. There are some alternatives available to the designer to handle this problem. Basically, the capacitive loading of the data bus slows down the response time, even though DC specifications are still met. For systems operating with a relatively slow CPU clock frequency, more time is available in which to establish proper logic levels on the bus and therefore higher capacitive loads can be driven (see Typical Performance Curves). At higher CPU clock frequencies time can be extended for I/O reads (and/or writes) by inserting wait states (8080) or using clock-extending circuits (6800). VIN + fSADJ VMAX 1.5 VMAX VMIN – 256 ----------------------------------------- – = CLK R 4 CLK IN CLK ADC0803- ADC0804 fCLK 19 R C 1 1.1 RC R 10k FIGURE 16. SELF-CLOCKING THE A/D 11 12 13 14 15 16 17 18 20 19 10 9 8 7 6 5 4 3 2 1 ADC0803 - ADC0804 WR RD CS INTR CLK IN VIN (-) VIN (+) DGND VREF/2 AGND DB1 DB0 DB4 DB3 DB2 DB7 DB6 DB5 CLK R V+ 10K 5V (VREF) 10 F + DATA START ANALOG INPUTS 150pF OUTPUTS N.O. MSB LSB FIGURE 17. FREE-RUNNING CONNECTION |
Podobny numer części - ADC0803 |
|
Podobny opis - ADC0803 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |