 |
Zakładka z wyszukiwarką danych komponentów |
|
|
Zakładka z wyszukiwarką danych komponentów |
|
CS5466 Arkusz danych(PDF) 11 Page - Cirrus Logic |
|
||||||||||||||||||||||||||||||
CS5466 Arkusz danych(HTML) 11 Page - Cirrus Logic |
|
|
11 / 16 page  CS5466 11 5. FUNCTIONAL DESCRIPTION 5.1 Analog Inputs The CS5466 is equipped with two fully differential input channels. The inputs VIN ± and IIN± are designated as the voltage and current channel inputs, respectively. The full-scale differential input voltage for the current and voltage channel is ±250 mVP. 5.1.1 Voltage Channel The output of the line voltage resistive divider or trans- former is connected to the VIN+ and VIN- input pins of the CS5466. The voltage channel is equipped with a 10x fixed gain amplifier. The full-scale signal level that can be applied to the voltage channel is ±250 mV. If the input signal is a sine wave the maximum RMS voltage is: which is approximately 70.7% of maximum peak volt- age. 5.1.2 Current Channel The output of the current sense resistor or transformer is connected to the IIN+ and IIN- input pins of the CS5466. To accommodate different current sensing de- vices the current channel incorporates a Programmable Gain Amplifier (PGA) that can be set to one of four input ranges. Input pins IGAIN1 and IGAIN0 (See Table 1) define the PGA’s four gain selections and correspond- ing maximum input signal level. For example if IGAIN1=IGAIN0=0, the current channel’s PGA gain is set to 10x. If the input signals are pure si- nusoids with zero phase shift, the maximum peak differ- ential signal on the current or voltage channel is ±250 mVP. The input signal levels are approximately 70.7% of maximum peak voltage producing a full scale energy pulse registration equal to 50% of absolute max- imum energy pulse registration. This will be discussed further in Section 5.3. 5.2 High-Pass Filter By removing the offset from either channel, no error component will be generated at dc when computing the average real power. Input pin HPF defines the three op- tions; – High-Pass Filter (HPF) is disabled when pin HPF is connected high. – HPF is enabled in the voltage channel when pin HPF is connected low. – HPF is enabled in the current channel when pin HPF is connected to pin FOUT. 5.3 Energy Pulse Outputs The CS5466 provides three output pins for energy reg- istration. The E1 and E2 pins provide a simple interface from which energy can be registered. These pins are designed to directly connect to a stepper motor or elec- tromechanical counter. The pulse rate on the E1 and E2 pins are in the range of 0 to 4 Hz and all frequency set- tings are optimized to be used with standard meter con- stants. The FOUT pin is designated for system calibration, the pulse rate can be selected to reach a fre- quency of 8000 Hz. 5.3.1 Pulse Output Format. The CS5466 produces alternating pulses on E1 and E2. This pulse format is designed to drive a stepper motor. Each pin produces active low pulses with a minimum pulse width of 250 ms when MCLK = 4.096 MHz. Refer to CS5466 Switching Characteristics on page 8 for tim- ing parameters. The FOUT pin issues active high pulses. The pulse width is equal to 90 ms (typical), unless the period falls below 180 ms. At this time the pulses will be equal to half the period. In mode 3 (FREQ2:0 = 3), the pulse width of all FOUT pulses is typically 20 µs regardless of the pulse rate (MCLK = 4.096 MHz). 5.3.2 Selecting Frequency of E1 and E2 The pulse rate on E1 and E2 can be set to one of four frequency ranges. Input pins FREQ1 and FREQ0 (See Table 2) determine the maximum frequency on E1 and E2 for pure sinusoidal inputs with zero phase shift. As shown in Figure 1 on page 8, the frequency of E2 is equal to the frequency of E1 with active low alternating pulses. As discussed in Section 5.1.2, the maximum frequency on the E1 and E2 output pins is equal to the selected fre- quency in Table 2 if the maximum peak differential sig- nal applied to both channels is a sine wave with zero phase shift. IGAIN1 IGAIN0 Maximum Input Range 0 0 ±250mV 10x 0 1 ±50mV 50x 1 0 ±25mV 100x 1 1 ±16.67mV 150x Table 1. Current Channel PGA Setting 250mV P 2 ----------------- 176.78mV RMS ≅ |
Podobny numer części - CS5466 |
|
Podobny opis - CS5466 |
|
|
|
Link URL |
| Polityka prywatności |
| ALLDATASHEET.PL |
| Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Polish ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
