Zakładka z wyszukiwarką danych komponentów |
|
LM2903-Q1 Arkusz danych(PDF) 17 Page - Texas Instruments |
|
LM2903-Q1 Arkusz danych(HTML) 17 Page - Texas Instruments |
17 / 33 page ±1 0 1 2 3 4 5 6 -0.25 0.25 0.75 1.25 1.75 2.25 Time (usec) 5mV OD 20mV OD 100mV OD C004 ±1 0 1 2 3 4 5 6 ±0.25 0.00 0.25 0.50 0.75 1.00 1.25 1.50 1.75 2.00 Time (usec) 5mV OD 20mV OD 100mV OD C006 17 LM2903-Q1, LM2903B-Q1 www.ti.com SLCS141I – MAY 2003 – REVISED JUNE 2020 Product Folder Links: LM2903-Q1 LM2903B-Q1 Submit Documentation Feedback Copyright © 2003–2020, Texas Instruments Incorporated 2. When IN- is higher than common mode and IN+ is within common mode, the output is low and the output transistor is sinking current 3. When IN+ is higher than common mode and IN- is within common mode, the output is high impedance and the output transistor is not conducting 4. When IN- and IN+ are both higher than common mode, the output is low and the output transistor is sinking current 8.2.2.2 Minimum Overdrive Voltage Overdrive Voltage is the differential voltage produced between the positive and negative inputs of the comparator over the offset voltage (VIO). In order to make an accurate comparison the Overdrive Voltage (VOD) should be higher than the input offset voltage (VIO). Overdrive voltage can also determine the response time of the comparator, with the response time decreasing with increasing overdrive. Figure 41 and Figure 42 show positive and negative response times with respect to overdrive voltage. 8.2.2.3 Output and Drive Current Output current is determined by the load/pull-up resistance and logic/pull-up voltage. The output current will produce a output low voltage (VOL) from the comparator. In which VOL is proportional to the output current. Use Figure 5 to determine VOL based on the output current. The output current can also effect the transient response. More will be explained in the next section. 8.2.2.4 Response Time The transient response can be determined by the load capacitance (CL), load/pull-up resistance (RPULLUP) and equivalent collector-emitter resistance (RCE). • The positive response time (τp) is approximately τP ~ RPULLUP × CL • The negative response time (τN) is approximately τN ~ RCE × CL – RCE can be determine by taking the slope of Figure 5 in it's linear region at the desired temperature, or by dividing the VOL by Iout 8.2.3 Application Curves The following curves were generated with 5 V on VCC and VLogic, RPULLUP = 5.1 kΩ, and 50 pF scope probe. Figure 41. Response Time for Various Overdrives (Positive Transition) Figure 42. Response Time for Various Overdrives (Negative Transition) |
Podobny numer części - LM2903-Q1_V02 |
|
Podobny opis - LM2903-Q1_V02 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |