Zakładka z wyszukiwarką danych komponentów |
|
AM79R79JC Arkusz danych(PDF) 10 Page - Advanced Micro Devices |
|
AM79R79JC Arkusz danych(HTML) 10 Page - Advanced Micro Devices |
10 / 20 page 10 Am79R79 Data Sheet Notes: 1. Unless otherwise noted, test conditions are BAT1 = –75 V, BAT2 = –24 V, VCC = +5 V, VNEG = –5 V, RL = 600 Ω, RDC1 = 80 kΩ, RDC2 = 20 kΩ, RD = 75 kΩ, no fuse resistors, CHP = 0.018 µF, CDC = 1.2 µF, D1 = D2 = 1N400x, two-wire AC input impedance (ZSL) is a 600 Ω resistance synthesized by the programming network shown below. RSGL = open, RSGH = open, RDCR = 2 kΩ, RRT1 = 430 kΩ, RRT2 = 12 kΩ, CRT = 1.5 µF, RSLEW = 100 kΩ, CSLEW = 0.33 µF. 2. a. Overload level is defined when THD = 1%. b. Overload level is defined when THD = 1.5%. 3. Balance return signal is the signal generated at VTX by VRX. This specification assumes that the two-wire AC load impedance matches the programmed impedance. 4. Not tested in production. This parameter is guaranteed by characterization or correlation to other tests. 5. This parameter is tested at 1 kHz in production. Performance at other frequencies is guaranteed by characterization. 6. Group delay can be greatly reduced by using a ZT network such as that shown in Note 1 above. The network reduces the group delay to less than 2 µs and increases 2WRL. The effect of group delay on linecard performance may also be compensated for by synthesizing complex impedance with the QSLAC or DSLAC device. 7. 70 Vpk provides 50 Vrms with a crest factor of 1.25 to a load of 1400 Ω with 2 • Rf = 100, and Rline = 70 Ω (1570 Ω). 8. Open Circuit VAB can be modified using RSGH. 9. RD must be greater than 56 kΩ. Refer to Table 2 for typical value of RLTH. 10. Lower power is achieved by switching into low-battery state in standby. Standby loop current is returned to VBAT1 regardless of the battery selected. Notes: * Only –1 and –2 performance grade devices support polarity reversal. ** For correct ground-start operation using Tip Open, VBAT1 on-hook battery must be used. Table 1. SLIC Decoding (DET) Output State C3 C2 C1 2-Wire Status E1 = 1 E1 = 0 Battery Selection 0 0 0 0 Open Circuit Ring trip Ring trip B2EN 1 0 0 1 Ringing Ring trip Ring trip 2 0 1 0 Active Loop detector Ground key 3 0 1 1 On-hook TX (OHT) Loop detector Ground key 4 1 0 0 Tip Open Loop detector Ground key B2EN = 1** 5 1 0 1 Standby Loop detector Ground key VBAT1 6* 1 1 0 Active Polarity Reversal Loop detector Ground key B2EN 7* 1 1 1 OHT Polarity Reversal Loop detector Ground key RT2 = 150 k Ω CT1 = 60 pF RT1 = 150 k Ω VTX RSN VRX RRX = 300 k Ω ~ |
Podobny numer części - AM79R79JC |
|
Podobny opis - AM79R79JC |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |