Zakładka z wyszukiwarką danych komponentów |
|
SI3200-X-FS Arkusz danych(PDF) 8 Page - Silicon Laboratories |
|
SI3200-X-FS Arkusz danych(HTML) 8 Page - Silicon Laboratories |
8 / 128 page Si3232 8 Preliminary Rev. 0.96 Table 4. AC Characteristics (VDD, VDD1–VDD4 = 3.13 to 3.47 V, TA = 0 to 70 °C for K-Grade, –40 to 85 °C for B-Grade) Parameter Test Condition Min Typ Max Unit TX/RX Performance TX Full Scale Output VTXP–XTXN 0.1 —VDD–0.1 V RX Full Scale Input VRXP–VRXN, ARX = 0 dB ARX = –3.52 dB ARX = –6.02 dB 0.25 0 0 — — — VDD–0.25 VDD VDD V V V Analog Input/Output Common Mode Voltage CMTXSEL = 1 CMTXSEL = 0 0.6 — — 1.5 1.5 — V V Overload Level ATX stage = 0 dB, THD = 1.5% 2.5 — — VPK Overload Compression Figure 4 — — Single Frequency Distortion1 2-wire to 4-wire or 4-wire to 2-wire: 200 Hz–3.4 kHz — –74 –68 dB 2-wire to 4-wire to 2-wire: 200 Hz–3.4 kHz — –74 –65 dB Signal-to-(Noise + Distortion) Ratio2 200 Hz–3.4 kHz Active off-hook, and OHT, any ZT — –74 –68 Intermodulation Distortion — — –41 dB Gain Accuracy2 2-Wire to 4-Wire or 4-Wire to 2-Wire, 1014 Hz, Any gain setting –0.25 — +0.25 dB Gain Distortion vs. Frequency –3 dB corners 0.01 — 10 kHz Gain Tracking 1014 Hz sine wave, reference level –10 dBm signal level: 3dB to –37dB –37dB to –50dB –50dB to –60dB — — — — — — ±0.25 ±0.5 ±1.0 dB dB dB Crosstalk between channels TX or RX to TX TX to RX to RX 0 dBm0, 300Hz to 3.4kHz 300Hz to 3.4kHz — — — — –75 –75 dB dB 2-Wire Return Loss3 200Hz to 3.4kHz 26 30 — dB Notes: 1. The input signal level should be 0 dBm0 for frequencies greater than 100 Hz. For 100 Hz and below, the level should be –10 dBm0. The output signal magnitude at any other frequency will be smaller than the maximum value specified. 2. Analog signal measured as VTIP – VRING. Assumes ideal line impedance matching. 3. VDD = 3.3 V, VBAT = –52 V, no fuse resistors, RL = 600 Ω, ZS = 600 Ω synthesized using RS register coefficients. 4. The level of any unwanted tones within the bandwidth of 0 to 4 kHz will not exceed –55 dBm. 5. The OBIAS and ABIAS registers program the dc bias current through the SLIC in the on-hook transmission and off- hook active conditions, respectively. This per-pin total current setting should be selected such that it can accommodate the sum of the metallic and longitudinal currents through each of the TIP and RING leads for a given application. |
Podobny numer części - SI3200-X-FS |
|
Podobny opis - SI3200-X-FS |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |