 |
Zakładka z wyszukiwarką danych komponentów |
|
|
Zakładka z wyszukiwarką danych komponentów |
|
ADSP-BF531SBB400 Arkusz danych(PDF) 8 Page - Analog Devices |
|
||||||||||||||||||||||||||||||
ADSP-BF531SBB400 Arkusz danych(HTML) 8 Page - Analog Devices |
|
|
8 / 60 page  Rev. D | Page 8 of 60 | August 2006 ADSP-BF531/ADSP-BF532 Although the ADSP-BF531/ADSP-BF532 processor provides a default mapping, the user can alter the mappings and priorities of interrupt events by writing the appropriate values into the interrupt assignment registers (IAR). Table 3 describes the inputs into the SIC and the default mappings into the CEC. Event Control The ADSP-BF531/ADSP-BF532 processor provides the user with a very flexible mechanism to control the processing of events. In the CEC, three registers are used to coordinate and control events. Each register is 16 bits wide: • CEC interrupt latch register (ILAT) – The ILAT register indicates when events have been latched. The appropriate bit is set when the processor has latched the event and cleared when the event has been accepted into the system. This register is updated automatically by the controller, but it may be written only when its corresponding IMASK bit is cleared. • CEC interrupt mask register (IMASK) – The IMASK regis- ter controls the masking and unmasking of individual events. When a bit is set in the IMASK register, that event is unmasked and will be processed by the CEC when asserted. A cleared bit in the IMASK register masks the event, preventing the processor from servicing the event even though the event may be latched in the ILAT register. This register may be read or written while in supervisor mode. (Note that general-purpose interrupts can be globally enabled and disabled with the STI and CLI instructions, respectively.) • CEC interrupt pending register (IPEND) – The IPEND register keeps track of all nested events. A set bit in the IPEND register indicates the event is currently active or nested at some level. This register is updated automatically by the controller but may be read while in supervisor mode. The SIC allows further control of event processing by providing three 32-bit interrupt control and status registers. Each register contains a bit corresponding to each of the peripheral interrupt events shown in Table 3. • SIC interrupt mask register (SIC_IMASK) – This register controls the masking and unmasking of each peripheral interrupt event. When a bit is set in the register, that peripheral event is unmasked and will be processed by the system when asserted. A cleared bit in the register masks the peripheral event, preventing the processor from servic- ing the event. • SIC interrupt status register (SIC_ISR) – As multiple peripherals can be mapped to a single event, this register allows the software to determine which peripheral event source triggered the interrupt. A set bit indicates the peripheral is asserting the interrupt, and a cleared bit indi- cates the peripheral is not asserting the event. • SIC interrupt wakeup enable register (SIC_IWR) – By enabling the corresponding bit in this register, a peripheral can be configured to wake up the processor, should the core be idled when the event is generated. (For more infor- mation, see Dynamic Power Management on Page 12.) Because multiple interrupt sources can map to a single general- purpose interrupt, multiple pulse assertions can occur simulta- neously, before or during interrupt processing for an interrupt event already detected on this interrupt input. The IPEND reg- ister contents are monitored by the SIC as the interrupt acknowledgement. The appropriate ILAT register bit is set when an interrupt rising edge is detected (detection requires two core clock cycles). The bit is cleared when the respective IPEND register bit is set. The IPEND bit indicates that the event has entered into the proces- sor pipeline. At this point the CEC will recognize and queue the next rising edge event on the corresponding event input. The minimum latency from the rising edge transition of the general- purpose interrupt to the IPEND output asserted is three core clock cycles; however, the latency can be much higher, depend- ing on the activity within and the state of the processor. DMA CONTROLLERS The ADSP-BF531/ADSP-BF532 processor has multiple, inde- pendent DMA controllers that support automated data transfers with minimal overhead for the processor core. DMA transfers can occur between the ADSP-BF531/ADSP-BF532 processor’s internal memories and any of its DMA-capable peripherals. Table 3. System Interrupt Controller (SIC) Peripheral Interrupt Event Default Mapping PLL Wakeup IVG7 DMA Error IVG7 PPI Error IVG7 SPORT 0 Error IVG7 SPORT 1 Error IVG7 SPI Error IVG7 UART Error IVG7 Real-Time Clock IVG8 DMA Channel 0 (PPI) IVG8 DMA Channel 1 (SPORT 0 Receive) IVG9 DMA Channel 2 (SPORT 0 Transmit) IVG9 DMA Channel 3 (SPORT 1 Receive) IVG9 DMA Channel 4 (SPORT 1 Transmit) IVG9 DMA Channel 5 (SPI) IVG10 DMA Channel 6 (UART Receive) IVG10 DMA Channel 7 (UART Transmit) IVG10 Timer 0 IVG11 Timer 1 IVG11 Timer 2 IVG11 PF Interrupt A IVG12 PF Interrupt B IVG12 DMA Channels 8 and 9 (Memory DMA Stream 1) IVG13 DMA Channels 10 and 11 (Memory DMA Stream 0) IVG13 Software Watchdog Timer IVG13 |
Podobny numer części - ADSP-BF531SBB400 |
|
Podobny opis - ADSP-BF531SBB400 |
|
|
Link URL |
| Polityka prywatności |
| ALLDATASHEET.PL |
| Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Polish ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
