www.ti.com

FUNCTIONAL DESCRIPTION

SN74GTLPH16912

18-BIT LVTTL-TO-GTLP UNIVERSAL BUS TRANSCEIVER

SCES288C – OCTOBER 1999 – REVISED JUNE 2005

The SN74GTLPH16912 is a medium-drive (50-mA), 18-bit UBT transceiver containing D-type latches and D-type

flip-flops for data-path operation in transparent, latched, clocked, or clock-enabled modes and can replace any of

the functions shown in Table 1. Data polarity is noninverting.

Table 1. SN74GTLPH16912 UBT Transceiver Replacement Functions

FUNCTION

8 BIT

9 BIT

10 BIT

16 BIT

18 BIT

Transceiver

'245, '623, '645

'863

'861

'16245, '16623

'16863

Buffer/driver

'241, '244, '541

'827

'16241, '16244, '16541

'16825

Latched transceiver

'543

'16543

'16472

Latch

'373, '573

'843

'841

'16373

'16843

Registered transceiver

'646, '652

'16646, '16652

'16474

Flip-flop

'374, '574

'821

'16374

Standard UBT

'16500, '16501

Universal bus driver

'16835

Registered transceiver with clock enable

'2952

'16470, '16952

Flip-flop with clock enable

'377

'823

'16823

Standard UBT with clock enable

'16600, '16601

SN74GTLPH16912 UBT transceiver replaces all above functions

Data flow in each direction is controlled by clock enables (CEAB and CEBA), latch enables (LEAB and LEBA),

clock (CLKAB and CLKBA), and output enables (OEAB and OEBA). CEAB and CEBA and OEAB and OEBA

control the 18 bits of data for the A-to-B and B-to-A directions, respectively.

For A-to-B data flow, when CEAB is low, the device operates on the low-to-high transition of CLKAB for the

flip-flop and on the high-to-low transition of LEAB for the latch path, i.e., if CEAB and LEAB are low, the A data is

latched, regardless of the state of CLKAB (high or low). If LEAB is high, the device is in transparent mode. When

OEAB is low, the outputs are active. When OEAB is high, the outputs are in the high-impedance state.

The data flow for B to A is similar to that of A to B, except CEBA, OEBA, LEBA, and CLKBA are used.

INPUTS

OUTPUT

MODE

B

CEAB

OEAB

LEAB

CLKAB

A

X

H

X

X

X

Z

Isolation

L

L

L

H

X

Latched storage of A data

L

L

L

L

X

X

L

H

X

L

L

True transparent

X

L

H

X

H

H

L

L

L

↑

L

L

Clocked storage of A data

L

L

L

↑

H

H

H

L

L

X

X

Clock inhibit

(1)

A-to-B data flow is shown. B-to-A data flow is similar, but uses CEBA, OEBA, LEBA, and CLKBA.

The condition when OEAB and OEBA are both low at the same time is not recommended.

(2)

Output level before the indicated steady-state input conditions were established, provided that

CLKAB was high before LEAB went low

(3)

Output level before the indicated steady-state input conditions were established

3