Zakładka z wyszukiwarką danych komponentów |
|
L6918A Arkusz danych(PDF) 6 Page - STMicroelectronics |
|
L6918A Arkusz danych(HTML) 6 Page - STMicroelectronics |
6 / 35 page L6918 L6918A 6/35 16 ISEN2 Channel 2 current sense pin. The output current may be sensed across a sense resistor or across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain or to the sense resistor through a resistor Rg in order to program the current intervention for each phase at 140% as follow: Where 35 µA is the current offset information relative to the Over Current condition (offset at OC threshold minus offset at zero load). The net connecting the pin to the sense point must be routed as close as possible to the PGNDS2 net in order to couple in common mode any picked-up noise. 17 OSC/INH FAULT Oscillator switching frequency pin. Connecting an external resistor from this pin to GND, the external frequency is increased according to the equation: Connecting a resistor from this pin to Vcc (12V), the switching frequency is reduced according to the equation: If the pin is not connected, the switching frequency is 300KHz. Forcing the pin to a voltage lower than 0.8V, the device stops operation and enters the inhibit state; all mosfets are turned OFF. The pin is forced high when an over voltage is detected. This condition is latched; to recover it is necessary turn off and on VCC. 18 SYNC_OUT Output synchronization signal. A 60 ° phase shift signal exits when the device works as a Slave while no signal exits when the device works as an adjustable. 19 SYNC / ADJ Slave or Adjustable operation. Connecting this pin to GND the device becomes an adjustable two-phase controller using an external reference for its regulation. No soft start is implemented in this condition, so it must be performed with external circuitry. The device switches using its internal oscillator according to the frequency set by ROSC. Leaving this pin floating, the device works as a Slave two-phase controller. It uses the reference sourced from the master device and an internal PLL locks the synchronization signal sourced from the master device. 20 SLAVE_OK Open-drain output used for start-up and to manage protections as shown in the timing diagram. Internally pulled-up. Connect together with other IC’s SLAVE_OK pin. Filter with 1nF capacitor vs. SGND. 21 SYNC_IN Synchronization input signal locked during the slave operation. Connect to the master SYNC_OUT pin. 22 VPROG_IN Reference voltage input used for voltage regulation. This pin must be connected together with the other’s slave (if present) to the VPROG_OUT pin of the master device. Filter to SGND with 1nF capacitor (a total 30nF distributed capacitance is allowed). If the device works as an Adjustable (SYNC/ADJ to GND), this is the reference used for the regulation. 23 PGOOD This pin is an open collector output and is pulled low if the output voltage is not within the above specified thresholds. It must be connected with the master’s PGOOD pin. If not used may be left floating. L6918 (SLAVE) PIN FUNCTION (continued) N. Name Description I OC Px 35 µAR g ⋅ R s ens e -------------------------- = f S 300KHz 14.82 10 6 ⋅ R OSC K Ω () ----------------------------- + = f S 300KHz 12.91 10 7 ⋅ R OSC K Ω () ----------------------------- + = |
Podobny numer części - L6918A |
|
Podobny opis - L6918A |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |