Zakładka z wyszukiwarką danych komponentów
  Polish  ▼
ALLDATASHEET.PL

X  

BD4153EFV Arkusz danych(PDF) 8 Page - Rohm

Numer części BD4153EFV
Szczegółowy opis  Power Switch ICs for ExpressCard
Download  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Producent  ROHM [Rohm]
Strona internetowa  http://www.rohm.com
Logo ROHM - Rohm

BD4153EFV Arkusz danych(HTML) 8 Page - Rohm

Back Button BD4153EFV Datasheet HTML 4Page - Rohm BD4153EFV Datasheet HTML 5Page - Rohm BD4153EFV Datasheet HTML 6Page - Rohm BD4153EFV Datasheet HTML 7Page - Rohm BD4153EFV Datasheet HTML 8Page - Rohm BD4153EFV Datasheet HTML 9Page - Rohm BD4153EFV Datasheet HTML 10Page - Rohm BD4153EFV Datasheet HTML 11Page - Rohm BD4153EFV Datasheet HTML 12Page - Rohm Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 18 page
background image
BD4153FV,BD4153EFV
Technical Note
8/17
www.rohm.com
2010.04 - Rev.B
© 2010 ROHM Co., Ltd. All rights reserved.
Description of operations
VCC
BD4153FV/EFV has an independent power input pin for an internal circuit operation in order to activate UVLO, Input logic,
and charge pump, the maximum current through which is rated to 2 mA. It is recommended to connect a bypass capacitor
of 0.1 μF or so to VCC pin.
EN
With an input of 2.3 volts or higher, this terminal turns to “High” level to activate the circuit, while it turns to “Low” level to
deactivate the circuit (with the standby circuit current of 35 μA), discharges each output and lowers output voltage If the input
is lowered to 0.8 volts or less.
V3_IN, V15_IN, and V3AUX_IN
These are the input terminals for each channel of a 3ch switch. V3_IN and V15_IN terminals have two pins each, which
should be short-circuited on the pc board with a thick conductor. And V3AUX IN terminal should be short-circuited to VCC
terminal. Through these three terminals, a big current runs (V3_IN: 1.35A, V3AUX_IN: 0.275 A, and V15_IN: 0.625 A). In
order to lower the output impedance of the power supply to be connected, it is recommended to provide ceramic capacitors
(of B-characteristics or better) between these terminals and ground; 1 μF or so between V3_IN and GND and between
V15_IN and GND, and 0.1 μF or so between V3AUX_IN and GND.
V3, V15, and V3AUX
These are the output terminals for each switch. V3 and V15 terminals have two pins each, which should be short-circuited
on the pc board and connected to an ExpressCard connector with a thick conductor as shortest as possible. In order to
stabilize the output, it is recommended to provide ceramic capacitors (of B-characteristics or better) between these terminals
and ground; 10 μF or so between V3 and GND and between V15 and GND, and 1 μF or so between V3AUX and GND.
CPPE#
The pin used to find whether a PCI-Express signal compatible card is provided or not. Turns to “High” level with an input of
2.3 volts or higher, which means that no card is provided, while it turns to “Low” level when the input is lowered to 0.8 volts or
less, which means that a card is provided. Controls turning ON/OFF of the switch according to the status of the system.
CPUSB#
The pin used to find whether a USB2.0 signal compatible card is provided or not. Turns to “High” level with an input of 2.3
volts or higher, which means that no card is provided, while it turns to “Low” level when the input is lowered to 0.8 volts or
less, which means that a card is provided. Controls turning ON/OFF of the switch according to the system status.
SYSR
The pin used to detect the system status. Turns to “High” level with an input of 2.3 volts or higher, which means that the
system is activated, while it turns to “Low” level when the input is lowered to 0.8 volts or less, which means that the system is
on standby.
PERST_IN#
The pin used to control a reset signal to a card (PERST#) from the system side. (Also referred to as “SysReset#” by
PCMCIA.) Turns to “High” level with an input of 2.3 volts or higher, and turns PERST# to “High” level AND with a “Power
Good” output. Turns to “Low” level and turns PERST# to “Low” level when the input is lowered to 0.8 volts or less.
PERST#
The pin used to provide a reset signal to a PCI-Express compatible card. The status is determined by each output,
PERST#_IN, CPPE# system status, and EN on/off status. Turns to “High” level and activates the PCI-Express compatible
card only if each output is within the “Power Good” threshold with the card kept inserted and with PERST_IN# turned to
“High” level.
PERST#_DELAY
Delay during which the level at PERST# pin turns from Low to High may be set with a capacitor externally applied. The
delay time is determined by the regulated current (2 μA), the reference voltage (0.7 volts) inside the IC and the capacitance
of the capacitor externally applied. The delay time is specified as “at least 1 ms” in “ExpressCard Standard”. It does not
synchronize with PERST_IN#, and it synchronizes only with a “Power Good” output inside the IC. Turns to “Low” level
when SW is turned OFF.
OC
Turns its output to “Low” level if an overcurrent condition is detected. This open drain output may be pulled up to 3.6 volts
power supply via resistor.
OC-Delay
Delay during which the level at OC pin turns from High to Low may be set with a capacitor externally applied. The delay
time is determined by the regulated current (2 μA), the reference voltage (0.7 volts) inside the IC and the capacitance of the
capacitor externally applied. May be used to control with the OC status fed back to the system. If fed back to EN terminal
of this IC, it may be used to turn OFF the output that is provided when an overcurrent condition is detected.


Podobny numer części - BD4153EFV

ProducentNumer częściArkusz danychSzczegółowy opis
logo
Rohm
BD4153EFV ROHM-BD4153EFV Datasheet
295Kb / 6P
   Power switch for ExpressCard
BD4153EFV ROHM-BD4153EFV Datasheet
689Kb / 18P
   Power Switch ICs for ExpressCardTM
More results

Podobny opis - BD4153EFV

ProducentNumer częściArkusz danychSzczegółowy opis
logo
Rohm
BD4153EFV ROHM-BD4153EFV Datasheet
295Kb / 6P
   Power switch for ExpressCard
BD4154FV ROHM-BD4154FV Datasheet
381Kb / 6P
   Power switch for ExpressCard
BD4153FV ROHM-BD4153FV Datasheet
275Kb / 6P
   Power switch for ExpressCard
BD4155FV ROHM-BD4155FV Datasheet
399Kb / 6P
   Power switch for ExpressCard
BD4154FV ROHM-BD4154FV_10 Datasheet
438Kb / 16P
   Power Switch IC for ExpressCard
BD4155FV ROHM-BD4155FV_10 Datasheet
473Kb / 17P
   Power Switch IC for ExpressCard
logo
Nuvoton Technology Corp...
W83L351YG NUVOTON-W83L351YG Datasheet
632Kb / 33P
   ExpressCard??Power Interface Switch
W83L351 NUVOTON-W83L351 Datasheet
632Kb / 33P
   ExpressCard??Power Interface Switch
logo
Texas Instruments
TPS2236 TI-TPS2236 Datasheet
953Kb / 26P
[Old version datasheet]   ExpressCard POWER INTERFACE SWITCH
logo
Winbond
W83L351 WINBOND-W83L351 Datasheet
1Mb / 33P
   ExpressCard??Power Interface Switch
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


Arkusz danych Pobierz

Go To PDF Page


Link URL




Polityka prywatności
ALLDATASHEET.PL
Czy Alldatasheet okazała się pomocna?  [ DONATE ] 

O Alldatasheet   |   Reklama   |   Kontakt   |   Polityka prywatności   |   Linki   |   Lista producentów
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com