Zakładka z wyszukiwarką danych komponentów |
|
FAN5701UMP30X Arkusz danych(PDF) 6 Page - Fairchild Semiconductor |
|
FAN5701UMP30X Arkusz danych(HTML) 6 Page - Fairchild Semiconductor |
6 / 12 page © 2009 Fairchild Semiconductor Corporation www.fairchildsemi.com FAN5701 • Rev. 1.0.3 6 Electrical Specifications Unless otherwise specified; VIN = 2.7V to 5.5V, TA = -40°C to +85°C, and EN = VIN. Typical values are VIN = 3.6V, TA = 25°C, ILED = 20mA, and LED cathode terminals = 0.4V. Circuit and components are according to Figure 1. Symbol Parameter Conditions Min. Typ. Max. Units Power Supplies and Thermal Protection IQ Quiescent Supply Current 1.5x Mode, No LEDs 4.4 mA 1x Mode, No LEDs 0.7 mA ISD Shutdown Supply Current EN = 0, VIN = 4.5V, TA=-40°C to +85°C 1.5 4.0 μA VUVLO Under-Voltage Lockout Threshold VIN Rising 2.55 2.70 V VIN Falling 2.20 2.40 VUVHYST Under-Voltage Lockout Hysteresis 150 mV OVP Over-Voltage Protection 6 V TLIMIT Thermal Shutdown 150 °C THYST Thermal Shutdown Hysteresis 20 °C LED Current Sinks ILED Absolute Current Accuracy VCATHODE=0.4V, See Options for ISET –10% ISET +10% mA ILED(MAX) Maximum Diode Current (3) ILED= ISET 30 mA ILED_MATCH LED Current Matching (4) VCATHODE=0.4V, ILED= ISET 0.4 3.0 % VDTH 1x to 1.5x Gain Transition Threshold LED Cathode Voltage Falling 100 mV VHR Current Sink Headroom (5) ILED = 90% ILED(NOMINAL) 65 mV Charge Pump ROUT Output Resistance 1.5x Mode 2.4 Ω 1x Mode 0.9 Ω fSW Switching Frequency 0.9 1.2 1.5 MHz tSTART Startup Time VOUT = 90% of Steady State 250 μs PWM Dimming fPWM PWM Dimming Frequency tON_LED = 15µs (Minimum) 20 kHz DPWM PWM Duty-Cycle fPWM = 100Hz 0.15 100.00 % Logic Inputs (EN, PWMA, PWMB) VIH HIGH-Level Input Voltage 1.2 V VIL LOW-Level Input Voltage 0.4 V VIMAX Maximum Input Voltage 1.8 5.5 V IIN Input Bias Current Input Tied to GND or VIN 0.01 1.00 μA Notes: 3. The maximum total output current for the IC should be limited to 180mA. The total output current can be split between the two groups (IDxA = IDxB = 30mA maximum). Under maximum output current conditions, special attention must be given to input voltage and LED forward voltage to ensure proper current regulation. See the Maximum Output Current section of the datasheet for more information . 4. For the two groups of current sinks on a part (GroupA and GroupB), the following are determined: the maximum sink current in the group (MAX), the minimum sink current in the group (MIN), and the average sink current of the group (AVG). For each group, two matching numbers are calculated: (MAX-AVG)/ AVG and (AVG-MIN)/AVG. The largest number of the two (worst case) is considered the matching figure for the group. The matching figure for a given part is considered to be the highest matching figure of the two groups. The typical specification provided is the most likely norm of the matching figure for all parts. 5. For each Dxx pin, headroom voltage is the voltage across the internal current sink connected to that pin. VHRx = VOUT - VLED. If headroom voltage requirement is not met, LED current regulation is compromised. |
Podobny numer części - FAN5701UMP30X |
|
Podobny opis - FAN5701UMP30X |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |