Zakładka z wyszukiwarką danych komponentów |
|
AD7854AQ Arkusz danych(PDF) 11 Page - Analog Devices |
|
AD7854AQ Arkusz danych(HTML) 11 Page - Analog Devices |
11 / 28 page AD7854/AD7854L REV. B –11– CALIBRATION REGISTERS The AD7854/AD7854L has 10 calibration registers in all, 8 for the DAC, 1 for offset and 1 for gain. Data can be written to or read from all 10 calibration registers. In self- and system calibration, the part automatically modifies the calibration registers; only if the user needs to modify the calibration registers should an attempt be made to read from and write to the calibration registers. Addressing the Calibration Registers The calibration selection bits in the control register CALSLT1 and CALSLT0 determine which of the calibration registers are addressed (See Table IV). The addressing applies to both the read and write operations for the calibration registers. The user should not attempt to read from and write to the calibration registers at the same time. Table IV. Calibration Register Addressing CALSLT1 CALSLT0 Comment 0 0 This combination addresses the Gain (1), Offset (1) and DAC Registers (8). Ten registers in total. 0 1 This combination addresses the Gain (1) and Offset (1) Registers. Two registers in total. 1 0 This combination addresses the Offset Register. One register in total. 1 1 This combination addresses the Gain Register. One register in total. Writing to/Reading from the Calibration Registers When writing to the calibration registers a write to the control register is required to set the CALSLT0 and CALSLT1 bits. When reading from the calibration registers a write to the con- trol register is required to set the CALSLT0 and CALSLT1 bits and also to set the RDSLT1 and RDSLT0 bits to 10 (this addresses the calibration registers for reading). The calibration register pointer is reset on writing to the control register setting the CALSLT1 and CALSLT0 bits, or upon completion of all the calibration register write/read operations. When reset it points to the first calibration register in the selected write/read sequence. The calibration register pointer points to the gain calibration register upon reset in all but one case, this case being where the offset calibration register is selected on its own (CALSLT1 = 1, CALSLT0 = 0). Where more than one cali- bration register is being accessed, the calibration register pointer is automatically incremented after each full calibration register write/read operation. The calibration register address pointer is incremented after the high byte read or write operation in byte mode. Therefore when reading from or writing to the calibra- tion registers, the low byte transfer must be carried out first, i.e., HBEN is at logic zero. The order in which the 10 calibration registers are arranged is shown in Figure 5. Read/Write opera- tions may be aborted at any time before all the calibration registers have been accessed, and the next control register write operation resets the calibration register pointer. The flowchart in Figure 6 shows the sequence for writing to the calibration registers. Figure 7 shows the sequence for reading from the cali- bration registers. CALIBRATION REGISTERS GAIN REGISTER OFFSET REGISTER DAC 1ST MSB REGISTER (1) (2) (3) DAC 8TH MSB REGISTER (10) CAL REGISTER ADDRESS POINTER CALIBRATION REGISTER ADDRESS POINTER POSITION IS DETERMINED BY THE NUMBER OF CALIBRATION REGISTERS ADDRESSED AND THE NUMBER OF READ/WRITE OPERATIONS. Figure 5. Calibration Register Arrangement When reading from the calibration registers there are always two leading zeros for each of the registers. WRITE TO CONTROL REGISTER SETTING STCAL = 0 AND CALSLT1, CALSLT0 = 00, 01, 10, 11 START CAL REGISTER POINTER IS AUTOMATICALLY RESET WRITE TO CAL REGISTER (ADDR1 = 1, ADDR0 = 0) CAL REGISTER POINTER IS AUTOMATICALLY INCREMENTED LAST REGISTER WRITE OPERATION OR ABORT ? FINISHED NO YES Figure 6. Flowchart for Writing to the Calibration Registers |
Podobny numer części - AD7854AQ |
|
Podobny opis - AD7854AQ |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |