Zakładka z wyszukiwarką danych komponentów |
|
AD9042ST Arkusz danych(PDF) 6 Page - Analog Devices |
|
AD9042ST Arkusz danych(HTML) 6 Page - Analog Devices |
6 / 24 page AD9042 –6– REV. A Harmonic Distortion The ratio of the rms signal amplitude to the rms value of the worst harmonic component, reported in dBc. Integral Nonlinearity The deviation of the transfer function from a reference line measured in fractions of 1 LSB using a “best straight line” determined by a least square curve fit. Minimum Conversion Rate The encode rate at which the SNR of the lowest analog signal frequency drops by no more than 3 dB below the guaranteed limit. Maximum Conversion Rate The encode rate at which parametric testing is performed. Output Propagation Delay The delay between the 50% point of the rising edge of ENCODE command and the time when all output data bits are within valid logic levels. Overvoltage Recovery Time The amount of time required for the converter to recover to 0.02% accuracy after an analog input signal 150% of full scale is reduced to midscale. Power Supply Rejection Ratio The ratio of a change in input offset voltage to a change in power supply voltage. Signal-to-Noise-and-Distortion (SINAD) The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, including harmonics but excluding dc. Signal-to-Noise Ratio (without Harmonics) The ratio of the rms signal amplitude (set at 1 dB below full scale) to the rms value of the sum of all other spectral components, excluding the first five harmonics and dc. Spurious-Free Dynamic Range The ratio of the rms signal amplitude to the rms value of the peak spurious spectral component. The peak spurious component may or may not be a harmonic. May be reported in dBc (i.e., degrades as signal levels is lowered), or in dBFS (always related back to converter full scale). Transient Response The time required for the converter to achieve 0.02% accuracy when a one-half full-scale step function is applied to the analog input. Two-Tone Intermodulation Distortion Rejection The ratio of the rms value of either input tone to the rms value of the worst third order intermodulation product; reported in dBc. Two-Tone SFDR The ratio of the rms value of either input tone to the rms value of the peak spurious component. The peak spurious component may or may not be an IMD product. May be reported in dBc (i.e., degrades as signal levels is lowered), or in dBFS (always related back to converter full scale). DIE LAYOUT AND MECHANICAL INFORMATION Die Dimensions . . . . . . . . . . . . . . . . 155 × 168 × 21 (±1) mils Pad Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 × 4 mils Metalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aluminum Backing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . None Substrate Potential . . . . . . . . . . . . . . . . . . . . . . . . . . . . GND Transistor Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2,605 Passivation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Oxynitride Die Attach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Silver Filled Bond Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gold DIE LAYOUT W/PAD LABELS DEFINITION OF SPECIFICATIONS Analog Bandwidth The analog input frequency at which the spectral power of the fundamental frequency (as determined by the FFT analysis) is reduced by 3 dB. Aperture Delay The delay between the 50% point of the rising edge of the ENCODE command and the instant at which the analog input is sampled. Aperture Uncertainty (Jitter) The sample-to-sample variation in aperture delay. Differential Nonlinearity The deviation of any code from an ideal 1 LSB step. Encode Pulse Width/Duty Cycle Pulse width high is the minimum amount of time that the ENCODE pulse should be left in logic “1” state to achieve rated performance; pulse width low is the minimum time ENCODE pulse should be left in low state. At a given clock rate, these specs define an acceptable Encode duty cycle. |
Podobny numer części - AD9042ST |
|
Podobny opis - AD9042ST |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |