Zakładka z wyszukiwarką danych komponentów |
|
ADXL362BCCZ-R2 Arkusz danych(PDF) 41 Page - Analog Devices |
|
ADXL362BCCZ-R2 Arkusz danych(HTML) 41 Page - Analog Devices |
41 / 44 page Data Sheet ADXL362 Rev. B | Page 41 of 44 USING AN EXTERNAL CLOCK The ADXL362 has a built-in clock that, by default, is used for clocked internal operations. If desired, an external clock can be provided and used. To use an external clock, the EXT_CLK bit (Bit 6) in the POWER_CTL register (Address 0x2D) must be set. Setting this bit reconfigures the INT1 pin to an input pin on which the clock can be provided. The external clock must operate at or below 51.2 kHz. Further information is provided in the External Clock section. USING SELF TEST The self test function, described in the Self Test section, is enabled via the ST bit in the SELF_TEST register, Address 0x2E. The recommended procedure for using the self test functionality is as follows: 1. Read acceleration data for the x-, y-, and z-axes. 2. Assert self test by setting the ST bit in the SELF_TEST register, Address 0x2E. 3. Wait 1/ODR for the output to settle to its new value. 4. Read acceleration data for the x-, y-, and z-axes. 5. Compare to the values from Step 1, and convert the difference from LSB to mg by multiplying by the sensitivity. If the observed difference falls within the self test output change specification listed in Table 1, then the device passes self test and is deemed operational. 6. Deassert self test by clearing the ST bit in the SELF_TEST register, Address 0x2E. The self test output change specification is given for VS = 2.0 V. Because the electrostatic force is proportional to VS2 and the sensitivity of the device is ratiometric to VS, the output change varies with VS. The scale factors shown in Table 22 can be used to adjust the expected self test output limits for different supply voltages, VS. Note that at higher voltages, self test deltas may exceed 1 g. If the measurement is performed with one axis experiencing 1 g due to gravity, and if the accelerometer is configured for a ±2 g measurement range, the axis that is aligned with the field of gravity may reach 2 g and its output clips (saturates to its full- scale value). To alleviate this, self test can be measured with the y-axis aligned with gravity (where the y-axis self test output change is negative), or with the accelerometer configured for a ±4 g or ±8 g measurement range. Table 22. Self Test Output Scale Factors for Different Supply Voltages, VS Supply Voltage, VS (V) Self Test Output Scale Factor 1.6 0.62 2.0 1.0 2.5 1.6 3.0 2.4 3.5 3.4 OPERATION AT VOLTAGES OTHER THAN 2.0 V The ADXL362 is tested and specified at a supply voltage of VS = 2.0 V; however, it can be powered with a VS as high as 3.3 V nominal (3.5 V maximum) or as low as 1.8 V nominal (1.6 V minimum). Some performance parameters change as the supply voltage changes, including the supply current (see Figure 30), noise (see Table 7 and Table 8), offset, sensitivity, and self test output change (see Table 22). Figure 48 shows the potential effect on 0 g offset at varying supply voltage. Data for this figure was calibrated to show 0 mg offset at 2.0 V. –100 –50 0 50 100 150 200 1.5 2.0 2.5 3.0 3.5 X-AXIS Y-AXIS Z-AXIS VS (V) Figure 48. 0 g Offset vs. Supply Voltage MECHANICAL CONSIDERATIONS FOR MOUNTING Mount the ADXL362 on the printed circuit board (PCB) in a location close to a hard mounting point of the PCB to the case. Mounting the ADXL362 at an unsupported PCB location, as shown in Figure 49, can result in large, apparent measurement errors due to undampened PCB vibration. Locating the accel- erometer near a hard mounting point ensures that any PCB vibration at the accelerometer is above the mechanical sensor resonant frequency of the accelerometer and, therefore, effec- tively invisible to the accelerometer. Multiple mounting points, close to the sensor, and/or a thicker PCB also help to reduce the effect of system resonance on the performance of the sensor. MOUNTING POINTS PCB ACCELEROMETERS Figure 49. Incorrectly Placed Accelerometers |
Podobny numer części - ADXL362BCCZ-R2 |
|
Podobny opis - ADXL362BCCZ-R2 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |