Zakładka z wyszukiwarką danych komponentów
  Polish  ▼
ALLDATASHEET.PL

X  

ADSP-2186MBCA-266 Arkusz danych(PDF) 9 Page - Analog Devices

Numer części ADSP-2186MBCA-266
Szczegółowy opis  DSP Microcomputer
Download  40 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Producent  AD [Analog Devices]
Strona internetowa  http://www.analog.com
Logo AD - Analog Devices

ADSP-2186MBCA-266 Arkusz danych(HTML) 9 Page - Analog Devices

Back Button ADSP-2186MBCA-266 Datasheet HTML 5Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 6Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 7Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 8Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 9Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 10Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 11Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 12Page - Analog Devices ADSP-2186MBCA-266 Datasheet HTML 13Page - Analog Devices Next Button
Zoom Inzoom in Zoom Outzoom out
 9 / 40 page
background image
REV. 0
ADSP-2186M
–9–
Interrupts
The interrupt controller allows the processor to respond to the
11 possible interrupts and reset with minimum overhead. The
ADSP-2186M provides four dedicated external interrupt input
pins:
IRQ2, IRQL0, IRQL1, and IRQE (shared with the PF7:4
pins). In addition, SPORT1 may be reconfigured for
IRQ0,
IRQ1, FI and FO, for a total of six external interrupts. The
ADSP-2186M also supports internal interrupts from the timer,
the byte DMA port, the two serial ports, software, and the power-
down control circuit. The interrupt levels are internally prioritized
and individually maskable (except power- down and reset). The
IRQ2, IRQ0, and IRQ1 input pins can be programmed to be
either level- or edge-sensitive.
IRQL0 and IRQL1 are level-
sensitive and
IRQE is edge-sensitive. The priorities and vector
addresses of all interrupts are shown in Table I.
Table I. Interrupt Priority and Interrupt Vector Addresses
Interrupt Vector
Source Of Interrupt
Address (Hex)
Reset (or Power-Up with PUCR = 1)
0000 (Highest Priority)
Power-Down (Nonmaskable)
002C
IRQ2
0004
IRQL1
0008
IRQL0
000C
SPORT0 Transmit
0010
SPORT0 Receive
0014
IRQE
0018
BDMA Interrupt
001C
SPORT1 Transmit or
IRQ1
0020
SPORT1 Receive or
IRQ0
0024
Timer
0028 (Lowest Priority)
Interrupt routines can either be nested with higher priority inter-
rupts taking precedence or processed sequentially. Interrupts
can be masked or unmasked with the IMASK register. Individual
interrupt requests are logically ANDed with the bits in IMASK;
the highest priority unmasked interrupt is then selected. The
power-down interrupt is nonmaskable.
The ADSP-2186M masks all interrupts for one instruction
cycle following the execution of an instruction that modifies the
IMASK register. This does not affect serial port autobuffering
or DMA transfers.
The interrupt control register, ICNTL, controls interrupt nest-
ing and defines the
IRQ0, IRQ1, and IRQ2 external interrupts
to be either edge- or level-sensitive. The
IRQE pin is an exter-
nal edge sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level sensitive interrupts.
The IFC register is a write-only register used to force and clear
interrupts. On-chip stacks preserve the processor status and are
automatically maintained during interrupt handling. The stacks
are twelve levels deep to allow interrupt, loop, and subroutine
nesting. The following instructions allow global enable or disable
servicing of the interrupts (including power down), regardless
of the state of IMASK. Disabling the interrupts does not affect
serial port autobuffering or DMA.
ENA INTS;
DIS INTS;
When the processor is reset, interrupt servicing is enabled.
LOW POWER OPERATION
The ADSP-2186M has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:
• Power-Down
•Idle
• Slow Idle
The CLKOUT pin may also be disabled to reduce external
power dissipation.
Power-Down
The ADSP-2186M processor has a low power feature that lets
the processor enter a very low-power dormant state through
hardware or software control. Following is a brief list of power-
down features. Refer to the ADSP-2100 Family User’s Manual,
“System Interface” chapter, for detailed information about the
power-down feature.
• Quick recovery from power-down. The processor begins
executing instructions in as few as 200 CLKIN cycles.
• Support for an externally generated TTL or CMOS processor
clock. The external clock can continue running during power-
down without affecting the lowest power rating and 200 CLKIN
cycle recovery.
• Support for crystal operation includes disabling the oscillator
to save power (the processor automatically waits approximately
4096 CLKIN cycles for the crystal oscillator to start or stabi-
lize), and letting the oscillator run to allow 200 CLKIN cycle
start-up.
• Power-down is initiated by either the power-down pin (
PWD)
or the software power-down force bit. Interrupt support allows
an unlimited number of instructions to be executed before
optionally powering down. The power-down interrupt also
can be used as a nonmaskable, edge-sensitive interrupt.
• Context clear/save control allows the processor to continue
where it left off or start with a clean context when leaving the
power-down state.
• The
RESET pin also can be used to terminate power-down.
• Power-down acknowledge pin indicates when the processor
has entered power-down.
Idle
When the ADSP-2186M is in the Idle Mode, the processor
waits indefinitely in a low-power state until an interrupt occurs.
When an unmasked interrupt occurs, it is serviced; execution
then continues with the instruction following the IDLE instruc-
tion. In Idle mode IDMA, BDMA and autobuffer cycle steals
still occur.


Podobny numer części - ADSP-2186MBCA-266

ProducentNumer częściArkusz danychSzczegółowy opis
logo
Analog Devices
ADSP-2186MBCA-266 AD-ADSP-2186MBCA-266 Datasheet
288Kb / 40P
   DSP Microcomputer
REV. 0
More results

Podobny opis - ADSP-2186MBCA-266

ProducentNumer częściArkusz danychSzczegółowy opis
logo
Analog Devices
ADSP-2185L AD-ADSP-2185L Datasheet
223Kb / 31P
   DSP Microcomputer
ADSP-2186M AD-ADSP-2186M Datasheet
288Kb / 40P
   DSP Microcomputer
REV. 0
ADSP-2183 AD-ADSP-2183 Datasheet
252Kb / 31P
   DSP Microcomputer
REV. C
ADSP-2184 AD-ADSP-2184 Datasheet
213Kb / 31P
   DSP Microcomputer
REV. 0
ADSP-2184L AD-ADSP-2184L Datasheet
216Kb / 31P
   DSP Microcomputer
REV. 0
ADSP-2184 AD-ADSP-2184_15 Datasheet
216Kb / 31P
   DSP Microcomputer
REV. 0
ADSP-2185 AD-ADSP-2185_15 Datasheet
291Kb / 32P
   DSP Microcomputer
REV. 0
ADSP-2189M AD-ADSP-2189M_15 Datasheet
244Kb / 32P
   DSP Microcomputer
REV. A
ADSP-21065L AD-ADSP-21065L Datasheet
488Kb / 44P
   DSP Microcomputer
REV. C
ADSP-2186BSTZ-160 AD-ADSP-2186BSTZ-160 Datasheet
261Kb / 36P
   DSP Microcomputer
REV. B
ADSP-2184BSTZ-160 AD-ADSP-2184BSTZ-160 Datasheet
216Kb / 31P
   DSP Microcomputer
REV. 0
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40


Arkusz danych Pobierz

Go To PDF Page


Link URL




Polityka prywatności
ALLDATASHEET.PL
Czy Alldatasheet okazała się pomocna?  [ DONATE ] 

O Alldatasheet   |   Reklama   |   Kontakt   |   Polityka prywatności   |   Linki   |   Lista producentów
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com