Zakładka z wyszukiwarką danych komponentów |
|
MAX3668 Arkusz danych(PDF) 5 Page - Maxim Integrated Products |
|
MAX3668 Arkusz danych(HTML) 5 Page - Maxim Integrated Products |
5 / 12 page +3.3V, 622Mbps SDH/SONET Laser Driver with Automatic Power Control _______________________________________________________________________________________ 5 1000 0.1 1.4 1.8 1.6 2.2 2.6 AVAILABLE BIAS CURRENT vs. MAXIMUM BIAS SET RESISTOR 1 10 100 RBIAS (k Ω) 2.0 2.4 VCC = +3.3V VCC = +3.3V, + 5V CLOSED-LOOP OPERATION VCC = +5V 0 5 15 10 20 25 -25 155 65 245 335 425 515 DISTRIBUTION OF MODULATION CURRENT STABILITY (WORST CASE) MODULATION DIODE CURRENT STABILITY (ppm/°C) TA = -40°C TO +85°C IMOD = 5mA 0 5 15 10 20 25 -52 -88 20 92 160 DISTRIBUTION OF MONITOR DIODE CURRENT STABILITY (WORST CASE) MONITOR DIODE CURRENT STABILITY (ppm/°C) TA = -40°C TO +85°C IMD = 18 µA Typical Operating Characteristics (continued) (VCC = +3.3V, TA = +25°C, unless otherwise noted.) Pin Description NAME FUNCTION 1, 2, 6, 15, 17, 20, 24 VCC Positive Supply Voltage 29 APCSET APC Set Resistor. A resistor connected from this pad to ground sets the desired average opti- cal power. The resulting current is equal to the desired DC monitor diode current. Connect a 100k Ω resistor from this pad to ground if APC is not used. PIN 3 DATA+ Positive PECL Data Input 4 DATA- Negative PECL Data Input 32 BIASMAX Maximum Bias Set Resistor. A resistor from this pad to ground sets the maximum laser bias current. The APC function can subtract from this maximum value but cannot add to it. This resistor controls the bias-current level when the APC loop is not used. 31 MODSET Modulation Set Resistor. A resistor from this pad to ground sets the laser modulation current. 5, 7, 8, 10, 14, 21, 22, 30 GND Ground 12, 13, 26, 27, 28 N.C. No Connection. Leave unconnected. 11 FAIL TTL Output. Indicates APC failure when low. Internally pulled high through a 6k Ω resistor. 9 ENABLE TTL/CMOS Enable Input. High for normal operation, low to disable laser bias and modulation currents. Internally pulled high. 16 BIAS Laser Bias Current Output. Isolate from laser with a ferrite bead. 19 OUT- Negative Modulation Current Output. IMOD flows into this pad when the input signal is low. Connect this pad to VCC through a 6.3 Ω resistor. 18 OUT+ Positive Modulation Current Output. IMOD flows into this pad when the input signal is high. Connect this pad to AC coupling network. 23 MD Monitor Photodiode Connection. Connect this pad to the monitor photodiode anode. A capaci- tor to ground is required to filter high-speed AC monitor photocurrent. 25 CAPC APC Compensation Capacitor. A 0.1µF capacitor connected from this pad to ground controls the dominant pole of the automatic power control (APC) feedback loop. |
Podobny numer części - MAX3668 |
|
Podobny opis - MAX3668 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |