Zakładka z wyszukiwarką danych komponentów |
|
DM9102AT Arkusz danych(PDF) 9 Page - List of Unclassifed Manufacturers |
|
DM9102AT Arkusz danych(HTML) 9 Page - List of Unclassifed Manufacturers |
9 / 77 page DM9102A Single Chip Fast Ethernet NIC controller Final 9 Version: DM9102A-DS-F03 August 28, 2000 the WOL as pulse or DC signal. 0 = WOL pulse mode (default) 1 = WOL DC mode BPAD2 is also a reset latch pin. It is Boot ROM address and data bus when normal operation. When at power on reset, it is used to pull up or down externally through a resister to select the PME as pulse or DC signal. 0 = PME pulse mode (default) 1 = PME DC mode BPAD7 is also a reset latch pin. It is Boot ROM address and data bus when normal operation. When at power on reset, it is used to pull up or down externally through a resister to select LED mode. 0 = LED mode 0 (default) 1 = LED mode 1 72 BPCS# O Boot ROM Chip Select Boot ROM or external register chip select signal. 73 BPA0/WMODE O, LI Boot ROM address line/WOL mode selection This multiplexed pin acts as boot ROM address bit 0 output signal during normal operation. When at power on reset, it used to select the type of WOL signal. 0 = WOL high active (default) 1 = WOL low active 74 BPA1/PCIMODE# I/O, LI Boot ROM address line / PCI mode selection This multiplexed pin acts as the boot ROM address bit 1 output signal during normal operation. When RST# is active (low), it acts as the input system type. If the DM9102A is used in a CardBus system, this pin should be connected to a pull-up resistor; otherwise, the DM9102A consider the host as a PCI system. 0 = PCI mode (default) 1 = CardBus mode 77 EEDI I EEPROM Data In The DM9102A will read the contents of EEPROM serially through this pin. 78 EEDO O EEPROM Data Out The DM9102A will use this pin to serially write opcodes, addresses and data into the EEPROM. 79 EECK O EEPROM Serial Clock This pin provides the clock for the EEPROM data transfer. 80 EECS O EEPROM Chip Select This pin will enable the EEPROM during loading of the Configuration Data. 81 SELROM I Multiplex or Director mode selection 0 = Multiplex mode (default) 1 = Direct mode 83,84,85,91,92,93,94 NC NC In Multiplex mode, these pins are not connected. |
Podobny numer części - DM9102AT |
|
Podobny opis - DM9102AT |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |