Zakładka z wyszukiwarką danych komponentów |
|
LM34CH Arkusz danych(PDF) 6 Page - National Semiconductor (TI) |
|
|
LM34CH Arkusz danych(HTML) 6 Page - National Semiconductor (TI) |
6 / 12 page Typical Performance Characteristics (Continued) Typical Applications The LM34 can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or ce- mented to a surface and its temperature will be within about 0.02˚F of the surface temperature. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature of the LM34 die would be at an intermediate temperature be- tween the surface temperature and the air temperature. This is expecially true for the TO-92 plastic package, where the copper leads are the principal thermal path to carry heat into the device, so its temperature might be closer to the air tem- perature than to the surface temperature. To minimize this problem, be sure that the wiring to the LM34, as it leaves the device, is held at the same tempera- ture as the surface of interest. The easiest way to do this is to cover up these wires with a bead of epoxy which will in- sure that the leads and wires are all at the same temperature as the surface, and that the LM34 die’s temperature will not be affected by the air temperature. The TO-46 metal package can also be soldered to a metal surface or pipe without damage. Of course in that case, the V − terminal of the circuit will be grounded to that metal. Alter- natively, the LM34 can be mounted inside a sealed-end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM34 and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where conden- sation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to in- sure that moisture cannot corrode the LM34 or its connec- tions. These devices are sometimes soldered to a small, light-weight heat fin to decrease the thermal time constant and speed up the response in slowly-moving air. On the other hand, a small thermal mass may be added to the sen- sor to give the steadiest reading despite small deviations in the air temperature. Capacitive Loads Like most micropower circuits, the LM34 has a limited ability to drive heavy capacitive loads. The LM34 by itself is able to drive 50 pF without special precautions. If heavier loads are anticipated, it is easy to isolate or decouple the load with a resistor; see Figure 3. Or you can improve the tolerance of capacitance with a series R-C damper from output to ground; see Figure 4. When the LM34 is applied with a 499 Ω load resistor (as shown), it is relatively immune to wiring ca- pacitance because the capacitance forms a bypass from ground to input, not on the output. However, as with any lin- ear circuit connected to wires in a hostile environment, its performance can be affected adversely by intense electro- magnetic sources such as relays, radio transmitters, motors with arcing brushes, SCR’s transients, etc., as its wiring can act as a receiving antenna and its internal junctions can act as rectifiers. For best results in such cases, a bypass capaci- tor from V IN to ground and a series R-C damper such as 75Ω in series with 0.2 or 1 µF from output to ground are often useful. These are shown in the following circuits. Noise Voltage DS006685-31 Start-Up Response DS006685-32 DS006685-6 www.national.com 6 |
Podobny numer części - LM34CH |
|
Podobny opis - LM34CH |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |