Zakładka z wyszukiwarką danych komponentów |
|
L6751TR Arkusz danych(PDF) 10 Page - STMicroelectronics |
|
L6751TR Arkusz danych(HTML) 10 Page - STMicroelectronics |
10 / 59 page Pin description and connection diagrams L6751 10/59 Doc ID 023992 Rev 1 A10 SOSC A Oscillator pin. It allows the switching frequency FSSW to be programmed for the single-phase section. The pin is internally set to 1.02 V, frequency for single-phase is programmed according to the resistor connected to GND or VCC with a gain of 11.5 kHz/µA. Leaving the pin floating programs a switching frequency of 230 kHz. See Section 10 for details. B9 SREF A The reference used for the single-phase section regulation is available on this pin with -125 mV offset. Connect through an RSREF-CSREF to GND to optimize DVID transitions. Connect through RSOS resistor to the SFB pin to implement small positive offset to the regulation. A11 TM A Thermal monitor sensor. Connect with proper network embedding NTC to the multi-phase power section. The IC senses the power section temperature and uses the information to define the VR_HOT signal and temperature monitoring. By programming proper TCOMP gain, the IC also implements load-line and IMON/ILIM thermal compensation for the multi-phase section. In JMode, the pin disables the single-phase section if shorted to GND. Pull up to VCC5 with 1 k Ω to disable thermal sensor. See Section 8 for details. B10 SPWM / SEN D PWM output. Connect to single-phase external driver PWM input. During normal operation the device is able to manage HiZ status by setting and holding the pin to a fixed voltage defined by PWMx strapping. Connect to VCC5 with 1 k Ω to disable the single-phase section. A12 SENDRV D Enable driver. CMOS output driven high when the IC commands the driver. Used in conjunction with the HiZ window on the SPWM pin to optimize the single- phase section overall efficiency. Connect directly to external driver enable pin. B11 ILIM A Multi-phase section current limit. A current proportional to the multi-phase load current is sourced from this pin. Connect through a resistor RLIM to GND. When the pin voltage reaches 2.5 V, the overcurrent protection is set and the IC latches. Filter through CLIM to GND to delay OC intervention. A13 VR_HOT D Voltage regulator HOT. Open drain output, this is an alarm signal asserted by the controller when the temperature sensed through the ST or TM pins exceed TMAX (active low). See Section 8 for details. B12 TCOMP A Thermal monitor sensor gain. Connect proper resistor divider between VCC5 and GND to define the gain to apply to the signal sensed by the TM to implement thermal compensation for the multi-phase section. Short to GND to disable temperature compensation (but not thermal sensor). See Section 8 for details. Table 2. Pin description (continued) Pin# Name Type Function |
Podobny numer części - L6751TR |
|
Podobny opis - L6751TR |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |