 |
Zakładka z wyszukiwarką danych komponentów |
|
|
Zakładka z wyszukiwarką danych komponentów |
|
HCPL3140 Arkusz danych(PDF) 7 Page - Agilent(Hewlett-Packard) |
|
||||||||||||||||||||||||||||||
HCPL3140 Arkusz danych(HTML) 7 Page - Agilent(Hewlett-Packard) |
|
|
7 / 16 page  7 Switching Specifications (AC) Over recommended operating conditions unless otherwise specified. Test Parameter Symbol Min. Typ. Max. Units Conditions Fig. Note Propagation Delay Time to tPLH 0.1 0.2 0.7 µs Rg = 47 Ω, 10,11, 14 High Output Level Cg = 3 nF, 12,13, Propagation Delay Time to tPHL 0.1 0.3 0.7 µs f = 10 kHz, 14,17 Low Output Level Duty Cycle = Propagation Delay PDD -0.5 0.5 µs 50%, 10 Difference Between Any IF = 8 mA, Two Parts or Channels VCC = 30 V Rise Time tR 50 ns Fall Time tF 50 ns Output High Level Common |CMH| 10 kV/ µsTA = 25°C, 18 11 Mode Transient Immunity VCM = 1 kV Output Low Level Common |CML| 10 kV/ µs18 12 Mode Transient Immunity Package Characteristics Test Parameter Symbol Min. Typ. Max. Units Conditions Fig. Note Input-Output Momentary VISO 2500 Vrms TA=25°C, 8,9 Withstand Voltage RH<50% for Input-Output Resistance RI-O 1012 Ω VI-O=500 V 9 Input-Output Capacitance CI-O 0.6 pF Freq=1 MHz Notes: 1. Derate linearly above 70 °C free air temperature at a rate of 0.3 mA/°C. 2. Maximum pulse width = 10 µs, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with IO peak minimum = 0.4 A. See Application section for additional details on limiting IOL peak. 3. Derate linearly above 85 °C, free air temperature at the rate of 4.0 mW/°C. 4. Input power dissipation does not require derating. 5. Maximum pulse width = 50 µs, maximum duty cycle = 0.5%. 6. In this test, VOH is measured with a DC load current. When driving capacitive load VOH will approach VCC as IOH approaches zero amps. 7. Maximum pulse width = 1 ms, maximum duty cycle = 20%. 8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 3000 V rms for 1 second (leakage detection current limit II-O ≤ 5 µA). This test is performed before 100% production test for partial discharge (method B) shown in the VDE 0884 Insulation Characteristics Table, if applicable. 9. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together. 10. PDD is the difference between tPHL and tPLH between any two parts or channels under the same test conditions. 11. Common mode transient immunity in the high state is the maximum tolerable |dVcm/dt| of the common mode pulse VCM to assure that the output will remain in the high state (i.e. Vo > 6.0 V). 12. Common mode transient immunity in a low state is the maximum tolerable |dVCM/dt| of the common mode pulse, VCM, to assure that the output will remain in a low state (i.e. Vo < 1.0 V). 13. This load condition approximates the gate load of a 1200 V/25 A IGBT. 14. The power supply current increases when operating frequency and Qg of the driven IGBT increases. |
Podobny numer części - HCPL3140 |
|
Podobny opis - HCPL3140 |
|
|
|
Link URL |
| Polityka prywatności |
| ALLDATASHEET.PL |
| Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
Polish ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
