Zakładka z wyszukiwarką danych komponentów |
|
ST92F120JR1Q7 Arkusz danych(PDF) 6 Page - STMicroelectronics |
|
ST92F120JR1Q7 Arkusz danych(HTML) 6 Page - STMicroelectronics |
6 / 324 page 6/324 ST92F120 - GENERAL DESCRIPTION 1.2 PIN DESCRIPTION AS. Address Strobe (output, active low, 3-state). Address Strobe is pulsed low once at the begin- ning of each memory cycle. The rising edge of AS indicates that address, Read/Write (RW), and Data signals are valid for memory transfers. DS. Data Strobe (output, active low, 3-state). Data Strobe provides the timing for data movement to or from Port 0 for each memory transfer. During a write cycle, data out is valid at the leading edge of DS. During a read cycle, Data In must be valid pri- or to the trailing edge of DS. When the ST9 ac- cesses on-chip memory, DS is held high during the whole memory cycle. RESET. Reset (input, active low). The ST9 is ini- tialised by the Reset signal. With the deactivation of RESET, program execution begins from the Program memory location pointed to by the vector contained in program memory locations 00h and 01h. RW. Read/Write (output, 3-state). Read/Write de- termines the direction of data transfer for external memory transactions. RW is low when writing to external memory, and high for all other transac- tions. OSCIN, OSCOUT. Oscillator (input and output). These pins connect a parallel-resonant crystal, or an external source to the on-chip clock oscillator and buffer. OSCIN is the input of the oscillator in- verter and internal clock generator; OSCOUT is the output of the oscillator inverter. HW0SW1. When connected to VDD through a 1K pull-up resistor, the software watchdog option is selected. When connected to VSS through a 1K pull-down resistor, the hardware watchdog option is selected. VPWO. This pin is the output line of the J1850 pe- ripheral (JBLPD). It is available only on some de- vices. On devices without JBLPD peripheral, this pin must not be connected. P0[7:0], P1[2:0] or P1[7:0] (Input/Output, TTL or CMOS compatible). 16 lines providing the external memory interface for addressing 2K or 64 K bytes of external memory. P0[7:0], P1[2:0], P2[7:0], P3[7:4], P4[7:4], P5[7:0], P6[5:2,0], P7[7:0] I/O Port Lines (Input/ Output, TTL or CMOS compatible). I/O lines grouped into I/O ports of 8 bits, bit programmable under software control as general purpose I/O or as alternate functions. P1[7:3], P3[3:1], P4[3:0], P6.1, P8[7:0], P9[7:0] Additional I/O Port Lines available on PQFP100 versions only. AVDD Analog VDD of the Analog to Digital Convert- er (common for A/D 0 and A/D 1). AVSS Analog VSS of the Analog to Digital Convert- er (common for A/D 0 and A/D 1). VDD Main Power Supply Voltage. Four pins are available. The pins are internally connected. VSS Digital Circuit Ground. Four pins are availa- ble. The pins are internally connected. VTEST Power Supply Voltage for Flash test pur- poses. This pin is bonded and must be kept to 0 in User mode. VREG 3V regulator output (on future versions, i.e. ST92F124 and ST92F150). 1.2.1 Electromagnetic Compatibility (EMC) To reduce the electromagnetic interference the fol- lowing features have been implemented: – A low power oscillator is included with a control- led gain to reduce EMI and the power consump- tion in Halt mode. – Four pairs of digital power supply pins (VDD, VSS) are located on each side of the package. – Digital and analog power supplies are complete- ly separated. – Digital power supplies for internal logic and I/O ports are separated internally. – Internal decoupling capacitance is located be- tween VDD and VSS. Note: Each pair of digital VDD/VSS pins should be externally connected by a 10 µF chemical pulling capacitor and a 100 nF ceramic chip capacitor. 1.2.2 I/O Port Alternate Functions Each pin of the I/O ports of the ST92F120 may as- sume software programmable Alternate Functions as shown in Section 1.3. 1.2.3 Termination of Unused Pins The ST9 device is implemented using CMOS tech- nology; therefore unused pins must be properly terminated in order to avoid application reliability problems. In fact, as shown in Figure 2, the stand- ard input circuitry is based on the CMOS inverter structure. 9 |
Podobny numer części - ST92F120JR1Q7 |
|
Podobny opis - ST92F120JR1Q7 |
|
|
Link URL |
Polityka prywatności |
ALLDATASHEET.PL |
Czy Alldatasheet okazała się pomocna? [ DONATE ] |
O Alldatasheet | Reklama | Kontakt | Polityka prywatności | Linki | Lista producentów All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |